Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
- 3. Engines
   - 3.1. Four-cylinder engines
      3.1.1. Removal and engine installation
      - 3.1.2. Dismantling and engine assemblage
         3.1.2.1. Removal and installation of a head of the block of cylinders
         3.1.2.2. Removal of a camshaft and pushers of valves
         3.1.2.3. Camshaft survey
         3.1.2.4. Definition of a technical condition of hydropushers of valves
         3.1.2.5. Installation of a camshaft and pushers of valves
         3.1.2.6. Removal and installation of valves (dismantling of a head of the block)
         3.1.2.7. Survey, дефектовка and repair of details of a head of the block of cylinders
         3.1.2.8. Backlashes between cams of a cam-shaft and pushers of valves
         3.1.2.9. A camshaft drive
         3.1.2.10. Removal and installation of an intermediate shaft
         3.1.2.11. Removal and flywheel installation
         3.1.2.12. Replacement of epiploons of a cranked shaft
         3.1.2.13. Removal and installation oil картера
         3.1.2.14. Removal, check and installation of the oil pump
         3.1.2.15. Dismantling of shatunno-piston group
         3.1.2.16. Survey and check of details of shatunno-piston group
         3.1.2.17. Assemblage of shatunno-piston group
         3.1.2.18. Removal, survey and installation of a cranked shaft
   + 3.2. Five-cylinder engines
   + 3.3. The diesel engine
+ 4. Cooling system
+ 5. An exhaust system
+ 6. The power supply system
+ 7. Transmission
+ 8. A running gear
+ 9. A steering
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment




eb52c3b6

3.1.2.10. Removal and installation of an intermediate shaft
THE GENERAL DATA

Cranked shaft and the block of cylinders

1 – the top persistent half ring;
2 – an epiploon of an intermediate shaft;
3 – an epiploon flange;
4 – an intermediate shaft;
5 – an epiploon of a cranked shaft;
6 – the holder of an epiploon;
7 – a lining;
8 – the bottom loose leaf of the radical bearing;
9 – a bolt of fastening of a cover of the radical bearing;
10 – a cover of the radical bearing;
11 – the bottom persistent half ring;
12 – a cranked shaft;
13 – the top loose leaf of the radical bearing

PERFORMANCE ORDER
1. To remove the ignition distributor (cм. Subsection 12.2.1.1 subitem 1-7) and the fuel pump (cм. Subsection 6.1.5 subitem 1-3).
2. To remove a belt of a drive of a camshaft (subsection 3.1.2.9 subitem 1-7 see).
3. To turn away a bolt of fastening and to remove a cogwheel of an intermediate shaft. To take out шпонку.
4. To turn away two bolts of a flange 3 epiploons of an intermediate shaft (fig. the Cranked shaft and the block of cylinders see) and to remove a flange with a sealing ring.
5. To take out an epiploon 2 of a flange 3.
6. Accurately to take out an intermediate shaft 4 of the block of cylinders.
7. To establish an intermediate shaft upside-down. Thus a new epiploon запрессовать in a flange and to grease a working edge of an epiploon with engine oil. Axial люфт a shaft should not exceed 0,25 mm.