Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
- 3. Engines
   - 3.1. Four-cylinder engines
      3.1.1. Removal and engine installation
      - 3.1.2. Dismantling and engine assemblage
         3.1.2.1. Removal and installation of a head of the block of cylinders
         3.1.2.2. Removal of a camshaft and pushers of valves
         3.1.2.3. Camshaft survey
         3.1.2.4. Definition of a technical condition of hydropushers of valves
         3.1.2.5. Installation of a camshaft and pushers of valves
         3.1.2.6. Removal and installation of valves (dismantling of a head of the block)
         3.1.2.7. Survey, дефектовка and repair of details of a head of the block of cylinders
         3.1.2.8. Backlashes between cams of a cam-shaft and pushers of valves
         3.1.2.9. A camshaft drive
         3.1.2.10. Removal and installation of an intermediate shaft
         3.1.2.11. Removal and flywheel installation
         3.1.2.12. Replacement of epiploons of a cranked shaft
         3.1.2.13. Removal and installation oil картера
         3.1.2.14. Removal, check and installation of the oil pump
         3.1.2.15. Dismantling of shatunno-piston group
         3.1.2.16. Survey and check of details of shatunno-piston group
         3.1.2.17. Assemblage of shatunno-piston group
         3.1.2.18. Removal, survey and installation of a cranked shaft
   + 3.2. Five-cylinder engines
   + 3.3. The diesel engine
+ 4. Cooling system
+ 5. An exhaust system
+ 6. The power supply system
+ 7. Transmission
+ 8. A running gear
+ 9. A steering
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment




eb52c3b6

3.1.2.15. Dismantling of shatunno-piston group
THE GENERAL DATA

Cranked shaft and details of shatunno-piston group

1 – a cranked shaft;
2 – the loose leaf шатунного the bearing;
3 – шатунный a bolt;
4 – a finger;
5 – маслосъемное a ring;
6 – компрессионное a ring;
7 – the piston;
8 – a lock ring;
9 – the plug of a head of a rod;
10 – a rod;
11 – a cover a rod; and
12 – a back epiploon of a cranked shaft;
13 – a flywheel;
14 – the bearing of a primary shaft of a transmission
PERFORMANCE ORDER
1. To remove a head of the block of cylinders (subsection 3.1.2.1 subitem 1-9 see).
2. To remove a belt of a drive of a camshaft (subsection 3.1.2.9 subitem 1-7 see).
3. To remove the oil pump (subsection 3.1.2.14 subitem 1-2 see).
4. To check up marks on rods and covers. If it is not visible, to mark rods and covers cylinder number.
5. To establish the piston of 1st cylinder in the bottom dead point (н.м.т.).
6. To turn away a nut of fastening and to uncover 11 rods (fig. the Cranked shaft and details of shatunno-piston group see). As the cover sits densely, to bring down it not strong blows of a hammer.
7. To take out from a cover the loose leaf 2 bearings, preliminary having marked it concerning a cover.
8. To push the piston in the cylinder so that a piston head left the cylinder, and then to take out the piston together with a rod. To take out the piston with a rod it is necessary cautiously not to damage a cylinder mirror.
9. To take out the loose leaf from the bottom head of a rod, preliminary having marked it concerning a rod.
10. Similarly to take out other pistons with rods.
11. To remove lock rings 8 and выпрессовать fingers 4 with the help оправки.
12. A stripper of piston rings to remove rings 5 and 6.