Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
- 3. Engines
   - 3.1. Four-cylinder engines
      3.1.1. Removal and engine installation
      - 3.1.2. Dismantling and engine assemblage
         3.1.2.1. Removal and installation of a head of the block of cylinders
         3.1.2.2. Removal of a camshaft and pushers of valves
         3.1.2.3. Camshaft survey
         3.1.2.4. Definition of a technical condition of hydropushers of valves
         3.1.2.5. Installation of a camshaft and pushers of valves
         3.1.2.6. Removal and installation of valves (dismantling of a head of the block)
         3.1.2.7. Survey, дефектовка and repair of details of a head of the block of cylinders
         3.1.2.8. Backlashes between cams of a cam-shaft and pushers of valves
         3.1.2.9. A camshaft drive
         3.1.2.10. Removal and installation of an intermediate shaft
         3.1.2.11. Removal and flywheel installation
         3.1.2.12. Replacement of epiploons of a cranked shaft
         3.1.2.13. Removal and installation oil картера
         3.1.2.14. Removal, check and installation of the oil pump
         3.1.2.15. Dismantling of shatunno-piston group
         3.1.2.16. Survey and check of details of shatunno-piston group
         3.1.2.17. Assemblage of shatunno-piston group
         3.1.2.18. Removal, survey and installation of a cranked shaft
   + 3.2. Five-cylinder engines
   + 3.3. The diesel engine
+ 4. Cooling system
+ 5. An exhaust system
+ 6. The power supply system
+ 7. Transmission
+ 8. A running gear
+ 9. A steering
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment




eb52c3b6

3.1.2.2. Removal of a camshaft and pushers of valves
THE GENERAL DATA

Head of the block of cylinders, camshaft and valves

1 – the final valve;
2 – the inlet valve;
3 – a lining;
4 – a valve spring internal;
5 – a valve spring external;
6 – a plate of springs of the valve;
7 – a valve pusher;
8 – a washer adjusting;
9 – a camshaft;
10 – a bearing cover;
11 – шпонка;
12 – a camshaft cogwheel;
13 – a washer;
14 – a bolt of fastening of a cogwheel;
15 – valve crackers;
16 – маслосъемный a cap;
17 – a basic washer of springs of the valve;
18 – the directing plug of the valve;
19 – a head of the block of cylinders;
20 – an epiploon

PERFORMANCE ORDER
1. To turn away a bolt of fastening of a cogwheel of a camshaft, to remove a wheel 12 and to take from a nest on a shaft segment шпонку 11.
2. To turn away a nut of fastening of covers of bearings 1, 3 and 5th, considering from a belt of a drive of a camshaft. To mark covers and to remove them.
3. To weaken and in regular intervals to turn away a nut of fastening of covers of bearings of 2nd and 4th. To mark covers and to remove them.
4. To remove a camshaft together with an epiploon.
5. To mark and remove pushers of valves. At each pusher from above in dredging the adjusting washer 8 is established. From pushers it is not recommended to take out adjusting washers not to mix them at assemblage.