Audi 100

1982-1990 of release

Repair and car operation

Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. An exhaust system
+ 6. The power supply system
+ 7. Transmission
+ 8. A running gear
+ 9. A steering
+ 10. Brake system
+ 11. A body
- 12. An electric equipment
   + 12.1. Electric equipment system
   - 12.2. Ignition system
      - 12.2.1. Transistor system of ignition
         12.2.1.1. Removal and installation of the distributor of ignition
         12.2.1.2. Dismantling and assemblage of the distributor of ignition
         12.2.1.3. Check and adjustment of a corner of an advancing of ignition
         12.2.1.4. Check of the coil of ignition
         12.2.1.5. Switchboard check
         12.2.1.6. Check of the gauge of the Hall
         12.2.1.7. Check of spark plugs
      + 12.2.2. Electronic system of ignition
      12.2.3. Contactless system of ignition FEI
   + 12.3. Electric schemes

12.2.1. Transistor system of ignition

12.2.1.1. Removal and installation of the distributor of ignition

THE GENERAL DATA

Elements of transistor system of ignition

1 – the switchboard;
2 – a coil arm;
3 – the ignition coil;
4 – the plug «15» (+);
5 – the plug «4»;
6 – the plug «1» (–);
7 – a wire to "the minus" plug of the storage battery;
8 – a spring of fastening of a cover of the distributor;
9 – vacuum-proof-reader;
10 – the holder of the distributor;
11 – a lining;
12 – the distributor case;
13 – a motionless plate;
14 – a washer;

15 – the Hall gauge (the gauge of operating impulses)
16 – a nest Pads;
17 – the screw;
18 – connecting колодка;
19 – a spark plug;
20 – a lock ring;
21 – a candle tip;
22 – the antidust screen;
23 – бегунок;
24 – a contact piece of coal;
25 – a distributor cover;
26 – the screen;
27 – a wire on "weight";
28 – an anchor

PERFORMANCE ORDER

1. To disconnect a wire from "the minus" plug of the storage battery.
2. To disconnect high-voltage wires from a distributor cover.
3. To disconnect a vacuum hose from the vacuum-proof-reader.
4. To disconnect колодку a gauge socket.
5. To establish a cranked shaft in position of century of m. т. The piston of 1st cylinder, corresponding to a compression step (subsection 3.2.2.1 see).
6. To turn away a bolt of fastening of the holder and to remove the holder.
7. To take out upwards the distributor of ignition and to remove a lining.
8. To establish the ignition distributor upside-down. Before installation to replace a lining. After distributor installation to adjust ignition.
9. If the distributor has been removed and before it you have not noted and have not remembered its position (the cranked shaft, etc. has been turned.), it is possible to arrive as follows. To establish a cranked shaft in position of century of m. т. The piston of 1st cylinder of a step of compression.
	10. To uncover the distributor, to turn бегунок so that the contact centre бегунка has been combined with a label on the distributor case.
11. To insert the distributor into an aperture in the block (head) of cylinders, slightly to turn clockwise. When приводная the distributor gear wheel will enter into gearing, the distributor will sit down into place and бегунок again выравняется with a label. To wrap and tighten bolts of fastening of the distributor.