Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. An exhaust system
+ 6. The power supply system
- 7. Transmission
   + 7.1. Coupling
   + 7.2. A mechanical drive of deenergizing of coupling
   + 7.3. A hydraulic drive
   - 7.4. A transmission
      - 7.4.1. Type 014 four-speed transmission
         7.4.1.1. Removal and dismantling
         7.4.1.2. Dismantling and assemblage of a primary shaft
         7.4.1.3. Dismantling and assemblage of a secondary shaft
         7.4.1.4. Assemblage and synchronizer dismantling
         7.4.1.5. Dismantling and differential assemblage
         7.4.1.6. Transmission assemblage
         7.4.1.7. Selection of a thickness of adjusting rings of back bearings
         7.4.1.8. The gear change lever
         7.4.1.9. Adjustment and installation of the mechanism of management by a gear change
      + 7.4.2. A five-speed transmission of type 013 or 093
      + 7.4.3. A five-speed transmission of types 016 and 012
      + 7.4.4. The mechanism of management of gear change КП of type 016
      + 7.4.5. An automatic transmission
   + 7.5. A drive of forward wheels
+ 8. A running gear
+ 9. A steering
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment




eb52c3b6

7.4.1.6. Transmission assemblage
PERFORMANCE ORDER
1. To establish in картер couplings an external ring of the forward bearing of a secondary shaft (if the bearing was replaced) and to fix its pin 22 (fig. the Secondary shaft of a transmission of type 014 see).
2. To establish differential in gathering in картер couplings.
3. To establish a cover of differential and to wrap bolts of its fastening by the moment 25 Н·м (2,5 кгс·м).
4. To establish flanges of a semiaxis and to wrap bolts of their fastening by the moment 20 Н·м (2,0 кгс·м), having fixed thus flanges from проворачивания.
5. To screw in a cover 3 (fig. type 014 Transmission see) boxes of differential the case of a reducer of a speedometer.
6. Запрессовать in картер 31 transmissions an external ring of the back bearing of a secondary shaft if the bearing was replaced.
7. To establish a plug of 13 switchings of 1st and 2nd transfers with a rod 14 in a groove муфты the synchronizer and together with secondary shaft 15 to establish in картер 31 transmissions.
8. To establish on a rod of a plug of switching of 1st and 2nd transfers a lead and to fix its spring pin.
9. To establish on an axis 23 intermediate gear wheel 35 backings and запрессовать an axis in картер transmissions.
10. To establish in картер 31 transmissions a primary shaft 12, having entered into gearing teeths of corresponding gear wheels.
11. Запрессовать adjusting pins 32 in картер transmissions.
12. To connect картер 31 transmissions with картером 5 couplings, having established between them a lining 6.
13. To wrap bolts of 33 fastenings картера transmissions to картеру couplings by the moment 25 Н·м (2,5 кгс·м).
14. To fix from axial moving a primary shaft, for example by means of a cross-beam 1 (2 – картер couplings).
15. Запрессовать in картер 31 (fig. type 014 Transmission see) transmissions the back ball bearing 30 primary shaft the closed part of a separator aside картера.
16. To establish a persistent washer 29 and a lock ring 28.
17. To remove a cross-beam and to include one of transfers, having fixed a primary shaft from a procollar. To wrap a nut 26 on the end of a secondary shaft the moment 100 Н·м (10 кгс·м) and законтрить it.
18. To establish rods of plugs in neutral position.
19. To put forward a rod of a plug of switching of 3rd and 4th transfers back and to insert into an aperture of a rod a pin 2 (fig. Carter of type 014 transmission see) замкового devices, preliminary having greased with its thin layer консистентной greasings. To establish a plug rod in neutral position.
20. To pick up for a thickness adjusting rings for correct installation of back bearings of primary and secondary shaft (subsection 7.4.1.7 see)
21. To establish spring скобу 1 (fig. Carter of the switching mechanism see) on the switch of 2 transfers, thus the spring leg should rest against the lever on a switch rod.
22. To establish in a back cover of 16 transmissions (fig. type 014 Transmission see) an adjusting washer 25 back bearings of a secondary shaft.
23. To establish all rods of plugs in neutral position and to get a lead of the switch of transfers to grooves of rods of plugs.
24. To establish a lining 21. Then to establish a cover of a transmission 16 on hairpins картера 31 transmissions, preliminary having turned it clockwise. To wrap bolts 17, 18 and 19 fastenings by the moment 25 Н·м (2,5 кгс·м).