Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. An exhaust system
+ 6. The power supply system
+ 7. Transmission
+ 8. A running gear
+ 9. A steering
- 10. Brake system
   10.1. Technical characteristics
   10.2. Adjustment of position of a pedal of a brake
   10.3. The main cylinder of a brake
   10.4. The brake mechanism of a forward wheel of mark Teves
   10.5. The brake mechanism of a forward wheel of mark GIRLING
   10.6. A brake disk
   10.7. The case скобы and the piston
   10.8. The drum-type brake mechanism of a back wheel
   10.9. A brake drum
   10.10. The wheel brake cylinder
   10.11. The disk brake mechanism of a back wheel
   10.12. A pressure regulator
   + 10.13. A lay brake
   10.14. Antiblocking system of brakes (ABS)
   10.15. Prorolling of brake system
+ 11. A body
+ 12. An electric equipment




eb52c3b6

10.5. The brake mechanism of a forward wheel of mark GIRLING
THE GENERAL DATA

The brake mechanism of a forward wheel of mark GIRLING

1 – колодка with wires of the gauge of deterioration brake колодок;
2 – a bolt;
3 – the case скобы;
4 – a directing finger;
5 – a bolt;

6 – the basis скобы;
7 – brake Pads;
8 – теплоизоляционная a lining;
9 – a rotary fist;
10 – a brake board;
11 – a brake disk

Replacement brake колодок

PERFORMANCE ORDER
1. To establish the car on a lay brake.
2. To establish basic бруски under back wheels.
3. To weaken bolts of fastening of a forward wheel.
4. To raise and establish on support a forward part of the car.
5. To remove a wheel, having turned on definitively fastening bolts.
6. To wash out the brake mechanism warm water and to dry. Application for clearing of brakes of gasoline, diesel fuel or any other mineral solvents is inadmissible.
7. To check up deterioration brake колодок through an aperture in the case скобы. If the thickness of frictional overlays колодок at least on the one hand makes less than 2 mm колодок it is necessary to replace complete sets from both parties of the car.
8. To disconnect колодку with wires from the gauge of deterioration brake колодок.
9. To turn away the bottom bolt of fastening of the case скобы, holding thus directing finger with a key.
10. To turn the case скобы downwards round an axis of the top finger. To mark brake Pads if will be established again old Pads as replacement internal and external колодок among themselves, and also between left and right wheels is inadmissible. It can lead to non-uniform braking. To remove brake Pads.
11. To clear of a dirt and a rust of a detail of a brake, especially seats brake колодок. Application for clearing of brakes of gasoline, diesel fuel or any other mineral solvents is inadmissible.
12. If are established new brake Pads it is necessary to press the piston into the cylinder accurately. Thus to watch, that the piston did not warp.
13. To check up correctness of installation теплоизоляционной linings.
14. To establish on the basis скобы brake Pads, watching that press springs stood vertically upwards and in parallel an upper edge brake колодок. Old Pads to establish according to earlier made marks.
15. To lower the case скобы.
16. To wrap the top bolt of fastening by the moment 35 Н·м (3,5 кгс·м), holding thus directing finger with a key.
17. To connect колодку with wires to the deterioration gauge колодок.
18. To establish a forward wheel and наживить fastening bolts.
19. To lower the car on the earth and to tighten bolts of fastening of a wheel in regular intervals on a diagonal the moment 110 Н·м (11,0 кгс·м).
20. To press some times a pedal of a brake for piston installation into position.
21. To check up level of a brake liquid in a tank and if necessary to add.