Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. An exhaust system
+ 6. The power supply system
+ 7. Transmission
- 8. A running gear
+ 8.1. A forward suspension bracket
- 8.2. A back suspension bracket
8.2.1. A telescopic rack
8.2.2. The back bridge
8.2.3. A brake drum
8.2.4. A nave of a back wheel (model with the disk brake mechanism)
8.2.5. Adjustment of bearings of a nave of a wheel
+ 9. A steering
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment
|
Telescopic rack of a back suspension bracket
|
1 – the shock-absorber;
2 – the bottom cup of a spring;
3 – a protective cap;
4 - a spring;
5 – a protective cover;
|
6 – the buffer of a course of compression;
7 – a rubber lining;
8 – the top cup of a spring;
9 – a rubber cap;
10 – a nut |
Telescopic rack of a back suspension bracket with system of stabilisation of a body
|
1 – the shock-absorber;
2 – the bottom cup of a spring;
3 – a protective cap;
4 – a spring;
5 – a protective cover with the buffer of a course of compression;
6 – a washer;
|
7 – a sealing ring;
8 – the union;
9 – a rubber lining;
10 – the top cup of a spring;
11 – a rubber cap;
12 – a nut |
Removal
| PERFORMANCE ORDER |
| 1. To establish an emphasis under forward wheels. |
| 2. To turn away bolts of fastening and to remove a back wheel. |
| 3. To establish a support under the back bridge and to lower the car, to load a telescopic rack. |
| 4. On models with system of stabilisation of a body to remove a protective cap and, having turned out the valve of release of air located on a tee, to merge a liquid. Then to disconnect the pipeline of system of stabilisation from the shock-absorber. |
| 5. To turn away a nut and to take out a bolt of the bottom fastening of a rack. |
| 6. To turn away three nuts of the top fastening of a rack. |
| 7. To remove a telescopic rack from the car. |
|
Dismantling, дефектовка and assemblage
| PERFORMANCE ORDER |
| 1. Dismantling, дефектовка and assemblage of a telescopic rack are made similarly telescopic rack of a forward suspension bracket (subsection 8.1.1 see.). |
|
2. To establish springs of telescopic racks of a back suspension bracket. A nut of the top fastening of the shock-absorber to tighten the moment 20 Н·м (2,0 кгс·м). |
|
Installation
| PERFORMANCE ORDER |
| 1. To insert from below a telescopic rack and to wrap three nuts of the top fastening by hand, without tightening. |
| 2. To insert a bolt of the bottom fastening and to wrap a new nut by hand, without tightening. |
| 3. To tighten three nuts of the top fastening by the moment 20 Н·м (2,0 кгс·м). |
| 4. On models with system of stabilisation of a body to connect the pipeline. |
| 5. To establish a wheel and наживить bolts of its fastening. |
| 6. To lower the car on wheels and to tighten bolts of fastening of a wheel in regular intervals the moment 110 Н·м (11,0 кгс·м). |
| 7. To tighten a bolt of the bottom fastening of the shock-absorber the moment 90 Н·м (9,0 кгс·м). |
| 8. On models with system of stabilisation of a body to make a trial trip. Thus the system is pumped over automatically. After that at the working engine to check up liquid level in a compensatory tank and to add if necessary to a mark «Max unbeladen». Thus the car should not be loaded. |
|
|
|
